Roller Wood Veneer Dryer Types-manufacture,factory,supplier from China

Why suggest you to choose Shine biomass burner roller veneer dryer ? 1. The biomass burner, a patented product independently developed by our company, can directly use crushed wood waste as fuel to provide a heat source for the dryer, no need to buy steam boiler or thermal oil again . which is energy-saving and environmentally friendly, and greatly reduces the drying cost. The comprehensive drying cost for one cbm is about $10 lower than thermal oil or steam boiler. 2.

When purchasing a veneer dryer, you should pay attention to: a good quality dryer has reasonable design, stable operation, energy saving and environmental protection, which can effectively improve the production capacity and quality of the dryer, and at the same time reduce the production cost of the dryer and the wear of parts , Consumption, reduce equipment maintenance costs. From the perspective of the performance of the veneer dryer, a good-quality dryer has the advantages of reasonable structure, low energy consumption, long service life, and durability.There are many types of kiln wood.

The veneer dryer needs to pay attention to some problems when drying wood. Before use, the heating fan should be started first, and when the drying temperature is reached, the speed regulating motor should be started. The veneer should enter from the feeding port longitudinally, the feeding should be straight, the veneer and the transmission roller should be connected at a 90-degree angle, and the veneer should be cut neatly before drying.

Xishuangbanna customers ordered two set  58 meters 4.5 meters wide double layer  roller veneer dryer ,which use thermal oil as fuel . They two veneer dryers were installed well and put into use successfully . they will dry the rubber veneers and welcome to visit and give suggestion. 

As the name suggests, wood drying equipment is used for wood drying. There are many types of similar equipment on the market now. Many manufacturers do not have a dedicated design team. Well, there is a big gap between the drying effect and the original promise. Therefore, when we choose, we must pay more attention to the comprehensive strength of the enterprise, and also consider what kind of product we need to buy. This is very important.

The Brazilian customer bought our 24m single-layer veneer drying equipment with our patented biomass burner,  the customer feedback that our equipment is very good, it can  achieve the expected output and  dried veneer moisture content is even, flat, no wrinkles.We have a professional R&D team that can design different models according to customer’s special requirement.

Why lumber can produce stem shrink, crack, bend be out of shape, mildew to wait for a phenomenon, it is to contain a lot of moisture as a result of lumber, go into the water branch in specific environment evaporates continuously, the quality that the nature of moisture evaporates can endanger lumber product seriously, appear a variety of problems.Therefore, wood needs to be forcibly dryer treated before it is made into various wood products.

Since its establishment in 1999, Shine Machinery has always adhered to the development concept of continuous innovation and provided excellent solutions for customers.At present, our largest roller veneer dryer has been installed and runs smoothly in South Africa, capable of drying approximately 230 cubic meters of veneer in 24 hours.Recently, our 6-layer and 6-meter wide veneer dryer has also unveiled its mysterious veil. Currently, research and development are progressing smoothly, with an expected hourly output of around 15-18 cubic meters, which will further enhance the user experience.

We have extensive experience in drying rubber wood veneer. Our dryer has the advantages of low card rate and easy maintenance of equipment.Reasonable roller diameter and roller spacing not only ensure that hot air can be evenly distributed on both sides of the veneer, but also greatly reduce the occurrence of veneer jamming. At the same time, the ellipticity of the roller does not exceed 100 um, and the straightness does not exceed 500 um, which also reduces the occurrence of jamming.

Recently, our Six-deck Roller Veneer Dryer carryed on a test run, and Peruvian customer visited the testing site. At present, the R&D work is progressing smoothly, and the new generation of automatic veneer loading machine meets expectations. The new dryer will undergo a fully automated upgrade to reduce labor costs while ensuring efficient and stable drying. It is expected to produce around 15-18 cubic meters per hour.